BUND, T-BRONX, T-NOTE ... e compagnia bella (V.M. 78 Anni)

ma va se 'sti .....erdaccioni di indici usa aiutano...

era sulle dirittura dei 30 forse 20 e quelli perdono :-x


meno male che c'e' Ditro che TIRA SU il morale :ops:
 
gastronomo ha scritto:
Fleursdumal ha scritto:
da ierisera iw è completamente inaffidabile continui blocchi :evil:

ma che qazzo stanno combinando con sti dati sull'ism già rettificati due volte, roba da zimbawe

Forse nel taroccare i dati ne han fatte più versioni e si sono dimenticati qual era quella "ufficiale" :smile:

:lol: :lol: :lol: :lol:
 
pazzia x follia me so preso un long di 10y per strappare qualche tick al computo totale dei miei spread 30-10y , long su pivot centrale con stop a 109 portato a pari se va sopra la parità and so on

1112371857squalo2[1].gif


oggi è il giorno degli squaloni, non so se ve ne siete accorti ma probabilmente a fine seduta il 10yt-note avrà fatto più volumi del Bund
 
ISM says non-manufacturing data released early
Fri Apr 1, 2005 10:56 AM ET
NEW YORK, April 1 (Reuters) - The Institute for Supply Management's March manufacturing and non-manufacturing indices were both reported on Friday, when only the manufacturing data were due, after the non-manufacturing report was issued early.
"Business Wire inadvertently released the non-manufacturing report today," said Terry Tracey, vice president of technology at ISM.

The non-manufacturing indicator had been slated for release on Tuesday. But it was transmitted on Business Wire at about 10 a.m. (1500 GMT) on Friday, when only the manufacturing report was due.

"That was done prematurely by us," said Phyllis Dantuono, senior vice president of national bureaus for Business Wire.

The manufacturing data were released a few minutes after 10 a.m. (1500 GMT).

Norbert Ore, chair of the ISM group's manufacturing business survey committee, said "there would (normally) be one final proofing before that information was released by BizWire. That was not done, but it would be rare that there would be an error because it was proofed numerous times."

Both reports, fully proofed, are now available on the Institute for Supply Management's Web site (www.ism.ws).

Quindi da quanto girano in anticipo i dati :-? ???
 
gastronomo ha scritto:
Fleursdumal ha scritto:
gastronomo ha scritto:
So le braghe so le braghe so, so ! Ditro sa come si dice ;)

che so queste? le paroline zozze che vi dite quando fate fikifiki? :eek: che rikkioni che siete :D :D :P

Vedi di fare il bravo altrimenti ti rispedisco a casa l'idraulico

... esatto ... e ringrazia gasto che è pure magnanimo ... che se fosse per mè verrei li io e poi vedi vè ....


1112371989ma_dove.jpg



:smile: :smile:
 
gastronomo ha scritto:
ISM says non-manufacturing data released early
Fri Apr 1, 2005 10:56 AM ET
NEW YORK, April 1 (Reuters) - The Institute for Supply Management's March manufacturing and non-manufacturing indices were both reported on Friday, when only the manufacturing data were due, after the non-manufacturing report was issued early.
"Business Wire inadvertently released the non-manufacturing report today," said Terry Tracey, vice president of technology at ISM.

The non-manufacturing indicator had been slated for release on Tuesday. But it was transmitted on Business Wire at about 10 a.m. (1500 GMT) on Friday, when only the manufacturing report was due.

"That was done prematurely by us," said Phyllis Dantuono, senior vice president of national bureaus for Business Wire.

The manufacturing data were released a few minutes after 10 a.m. (1500 GMT).

Norbert Ore, chair of the ISM group's manufacturing business survey committee, said "there would (normally) be one final proofing before that information was released by BizWire. That was not done, but it would be rare that there would be an error because it was proofed numerous times."

Both reports, fully proofed, are now available on the Institute for Supply Management's Web site (www.ism.ws).

Quindi da quanto girano in anticipo i dati :-? ???

io direi di annullare tutti i contratti post 17.00 :D
 
ecco la novella anche in idioma italico
USA: INDICE ISM SERVIZI, A MARZO SALITO A 63,1 (2)
(ANSA) - ROMA, 1 apr - L' Ism, nel comunicare l' andamento
del comparto manifatturiero, ha fatto in pratica una 'gaffe', in
quanto per errore è stato diffuso il dato relativo invece all'
altro indicatore, quello che riguarda cioé il comparto servizi.
Inizialmente, quindi, all' indice Ism per il comparto
industriale è stato attribuito a marzo il valore di 63,1 che in
seguito è stato prontamente rettificato appunto in 55,2. A quel
punto, però, lo stesso istituto ha dovuto ammettere di aver
resi noti in anticipo rispetto alla data prevista del 5 aprile
prossimo i dati relativi all' andamento dei servizi, ormai
divenuti di dominio pubblico. In pratica, è come se lo stesso
Ism avesse violato l' embargo relativo alla divulgazione dell'
indice relativo al comparto non manifatturiero, scambiando i
dati all' atto della diffusione dell' altro indicatore riferito
invece al settore dell' industria.
Per il resto, dai dati odierni è risultata un' accelerazione
sul versante dei prezzi industriali. Il sottoindice che misura
l' andamento dei prezzi pagati nel comparto manifatturiero a
marzo è salito infatti a 73,0 da 65,5. Tanto è bastato per
annullare il rialzo di Borsa e far recuperare terreno al
dollaro. Tanto più che anche l' andamento dei servizi - che
hanno un ruolo preponderante nell' economia statunitense - è
risultato appunto a marzo in forte crescita, contro le
previsioni. Si è riaffacciata così la prospettiva di una
stretta sui tassi da parte della Federal Reserve più dura di
quanto fatto fino ad oggi.
(ANSA).
 
ditropan ha scritto:
fed52 ha scritto:
---------------------------------------------------------------------------------
ciao, potresti postare il link di dove attingi le notizie riguardanti i dati?
scusami ma non ho ancora trovato un sito affidabile, nel senso che le riporti tempestivamente e soprattutto con le giuste considerazioni :)

... il mio tol ... nessun sito. :rolleyes:



si è vero, tra l'altro è anche il mio :) ma non riesco a fare copia/incolla....sai dirmi come fare?
 

Users who are viewing this thread

Back
Alto